How to hide the heating pipe

Building a new house, I want to do everything in the best way so that later I don’t have to redo anything. However, it does not always work out the way you want. It is often found that some kind of communication is visible - sewer pipes in the bathroom, gas channels in the kitchen or heating systems in the living rooms. Actually about how to hide the heating pipes and will be discussed in this article.

Pipe laying in the floor

What you need to know when laying pipes to hide them immediately? It is good if there is an opportunity to make shafts in the floor or walls so that the pipes of the right size fit into them. To do this, it is necessary to decide where and how the heating systems will pass, also to make sure that the pipes themselves and the joints do not leak and will last for a very long time. After such a thorough check, using a perforator, we make sufficiently wide and deep grooves in the necessary places, which can then be repaired. What - decide for yourself. After, we connect the pipes and put them in the cutouts in the concrete floor. The main thing here is that the top of the pipe is slightly below the floor. We close the grooves in the floor with a concrete or glue-cement mortar mixed with sand one by one. Pipes in the walls can be fixed with foam, alabaster or special wall fasteners. What do we get after such work? All pipes are beautifully and securely laid in the floor or hidden in the wall. This option is safe and does not harm the room.

The floor screed on top of the pipes must be sufficiently thick so that during operation of the room it will not break and the pipe in a certain place will not undergo deformation.

And do not forget about the presence of a pump in the system - pipes - laid without a slope, will not be able to properly heat the room, since the heat will not be able to pass through them normally.

The disadvantage of this option is obvious: in case of pipe leakage, the strobe will have to be broken and, possibly, to make an easy repair at the accident site if the walls are damaged.

Pipe masking

What to do if we purchased a new house, in which pipes were laid on top? Then there are several options. A more complicated way is to dismantle old pipes, as a rule, they are metal, and install new, plastic, for which you can make the above niches in the floor and walls. You can leave and metal pipes. According to most residents, new pipes do not heat as well as metal pipes. But when reworking heating pipes from metal there is one unpleasant feature. While plastic pipes are attached to each other quite easily, for the connection of metal pipes you need two components - electric welding and welding skills. Although this method is sometimes used, in general, it is rather complicated and time consuming.

Another simpler option is to close the pipes on top. You can do it like this:

• mount the box;
• disguise them against the walls;
• install furniture;
• apply a pattern that will give the pipes an exclusive look;
• in the end, just hang it with tulle or curtain.

Let's talk about the above methods, how to close the pipes. You can make a box - wooden or plasterboard. But do it better in cases where the pipes are held in the corner of the room vertically. For this you will need:

• some amount of metal profile;
• box of metal screws;
• plasterboard;
• putty.

The box, which is mounted in the bedroom or living room, can be covered with wallpaper in the style of the interior room. In this case, the corner tubes will not stand out.

Valves that block water access to batteries and similar places cannot be closed. You can leave the space open or make part of the box open (in the form of a door).

Another option - pipes laid horizontally, you can close the furniture, in which there is no back wall, and in the side sections to make cuts for pipes. This will perfectly solve the issue of disguise. But it is necessary to take into account one nuance. It lies in the fact that furniture needs to acquire the best quality materials, since cheap products simply crack off the temperature of the pipes during the winter period.

Actually, you can close the pipe around the perimeter of the entire wall, but this would entail a loss of usable area. For this purpose, a crate is applied to the walls, to which the wall panel is then attached. How to do it correctly, you can find out from experts or on websites on the Internet.

For those who do not have a lot of money to buy furniture, the following option will do: one of the cheapest. We go to the market, buy paint of the same color as the walls in the room, and beautifully put it on the pipes. Before this, it is important to give the pipe a very flat surface, and it is likely that you will have to coat them with a ground mixture. To achieve the desired effect, you can use sandpaper, and pipes, if necessary, to clean the layers of old paint.

Video

Alexey Zemskov will tell how to build a false wall to mask the heating and radiator pipes:

A photo