Deprecated: preg_match(): Passing null to parameter #2 ($subject) of type string is deprecated in /web/blog-oremonte.ru/page.php on line 13
How to glue the ceiling plinth 2 - Blog about repair

How to glue the ceiling plinth 2

20-02-2018
Useful

The ceiling plinth carries out several functions. Firstly, it gives the design of the walls and ceiling a special charm and beauty. Secondly, the plinth can hide some defects (for example, minor irregularities of the walls). In the article we will tell how to glue the ceiling plinth of foam plastic on wallpaper, stretch ceiling and putty, as well as how to glue it in the corners. What should be taken into account and what nuances to know?

We select the appropriate plinth and glue

Ceiling plinth or fillet is made from different materials. It can be wood, foam, gypsum or polyurethane. Therefore, in the first place, it is worthwhile to choose a suitable plinth for your case.

The most frequently purchased foam and polyurethane products. They have many common characteristics. Such fillets are made of polymeric compounds, have low cost and are fairly light.

The cheapest option is foam. But such a plinth has disadvantages. Polyfoam badly bends. If you need to go around large irregularities or glue over the corners, then such a plinth will just burst.

The foam does not like moisture, so it is not recommended to glue it in the bathroom.

Polyurethane is more flexible and not afraid of moisture. It is not much more expensive than foam products, but the quality is significantly different.

Polyurethane can be bent quite easily over large radii. It does not crumble and does not break.

Plaster or wooden fillets are quite expensive. In addition, they can not bend.

Such baseboards are glued only in rooms with absolutely correct geometrical dimensions and even surfaces. And, of course, the interior itself must fit.

If you have sorted out the choice of material, then it is worth counting the necessary amount of it. To do this, it is enough to measure the perimeter of the room. Then this figure is divided by the length of one fillet. Skirting boards can be produced in different lengths, but, as a rule, they are 2 meters.

Do not forget to determine the width of fillets.

If you have low ceilings, it is better to choose narrow baseboards. Also look at the texture and illumination, it should be suitable for both the design of the walls and the finishing of the ceiling.

Now let's talk about the glue. Acrylic and polymer adhesives are available. Each of them has its own characteristics. So, acrylics do not have a pungent smell (they are recommended by experts to use when repairing a children's room), which cannot be said about polymeric materials. But the latter can be used in rooms with high humidity. Choose a glue of well-known and well-established brands, as well as in accordance with the recommendations of the manufacturer of the plinth.

Training

Before pokleit plinth on the ceiling, it is necessary to do a little preparatory work. Firstly, the fillets themselves must be kept in the room for at least 24 hours. So they adapt to the environment. Secondly, the ceiling itself must be clean and smooth.

The ceiling plinth can be mounted before pasting the walls with wallpaper and after this work. The first method is the most time consuming, but at the same time it is more preferable. First, in this case, you can not change the fillets when changing wallpaper. And secondly, you will have the opportunity to seal the gap between the wall and the plinth, which can greatly spoil the appearance.

Experts recommend starting to glue from the corners. If in these places everything is done neatly and beautifully, then straight sections will pass quickly and efficiently. But to glue the corners is a special job. To do everything right, it is better to view the video with detailed instructions.

Sticking plinth in the corners

In order for the corner not to spoil the appearance of the entire decoration, the baseboard plates should be joined at an angle of 45 degrees. This can be achieved by using a mousse. This is a special device that allows you to cut at the right angle. You can also use the decorative corners. They are glued to the place of the joints and cover the cracks and seams formed.

Often apartments do not have the correct geometric shapes, which becomes very noticeable when gluing the cut baseboards at an angle of exactly 45 degrees. In this case, the cut angle will have to be aligned in place.

How to glue properly

Now let's talk about how to properly glue fillets. Glue is applied to the back side of the plinth using a trowel or construction gun. If you have a stretch ceiling, then glue is applied only to those areas that will be attached to the wall.

Then the fillet is pressed against the wall and against the ceiling (if it is not tensioned). Immediately hold for a long time is not necessary, let the glue dry a little. After a short time, press the strip tightly.

The glue sets quickly, so adjust the strip in advance. Fingerprints and dirt may remain on the light background of the plinth in order to avoid this, wash your hands more often during work.

If there are protrusions of adhesive mass, then they should be immediately removed with a cloth.

Instead of glue, you can use a finishing putty, adding PVA glue to it. Excess of this material often remains after repair. You can use the material of any manufacturer, there is no fundamental difference.

In case of using putty, the surface (where you will glue the fillets) must be wetted. Then a layer of putty is applied to the back side of the plinth using a spatula. Now press the plate against the ceiling and wall. Wipe off any excess putty with a cloth.

How to glue the baseboard wallpaper

As mentioned in the article, the plinth is best glued before the wallpaper is glued, but it happens that for some reason it did not work. In this case, you will have to glue the baseboard on the wallpaper.

Before starting the pasting work, make sure that the wallpaper is well glued to the wall (or ceiling). If this is not the case, then first glue the PVA glue on the wallpaper, let them dry and only after that glue the baseboard.

The process of gluing the plinth on the wallpaper is not much different from sticking it directly to the wall. The main difficulty is not to stain wallpaper with adhesive mixture. To do this, you can attach the plinth to the place where it will be glued and outline its edges with a simple pencil, leaving a barely noticeable line. The plinth is removed and the wallpaper near the line is taped with masking tape, which can be easily removed from the wallpaper. Now you can glue the plinth. After gluing, the excess glue is removed and then the masking tape is removed.

Hide the joints

Very often after gluing plinths, joints can become noticeable, with such a problem it is easy to cope. Such gaps can be sealed with white (or the color of your fillet) sealant.

There is another way. To do this, prepare a liquid putty. Using a brush to paint all the skirting. After drying, walk on them with a fine sandpaper. Thus, the plinth and the ceiling will become one, and the gaps between the strips will be difficult to make out.

If white plinths are installed in the room, then it is advisable to paint them. This will keep the color much longer. For this procedure, water-based, latex or acrylic paints are used. Often use the first option. But if you use nitrocolors, the surface must first be primed.

Coloring can be carried out a day after installation of the plinth. So you give the glue to finally grab. When painting, be careful. It is better to use a small brush, otherwise there is a risk to paint over all the space around the fillets.

A photo