Fence and other additional elements

To protect and decorate fences made of corrugated board, brick, stone, concrete and picket fence, a U-shaped fence panel is used, which is worn on the edge and can be fixed either with glue or aluminum rivets.

This design can be of any color provided by the RAL table, so it will be harmoniously combined with any color sections.

Multi-colored plank for fences (PS)

Useful information about the additional elements of the fence

Trims and caps on a brick fence

Such structural materials are related to the additional elements of fencing, so the overall design can do without their use. But every little thing always has its own purpose, so the use of slats for fences will never be superfluous, but only emphasizes the integrity of the composition.

It is about this material that will be discussed below and the video in this article will help us better understand this topic.

Specifications

Brick fences

• As a rule, intake strips are made by cold rolling of zinc-coated steel sheets, without any seams or rivets.. As mentioned above, such an additional element can be in harmony in color with any shades of fencing and for this purpose polyester or pural is used, which, in fact, allows the product to reflect any RAL value of the table. In addition, polymer coatings allow you to paint the construction material under any tree or natural decorative stone.

The use of fence strips for corrugated

• Probably, most often such strips are used for corrugated fences, because they not only decorate and protect the edges from moisture, but also give the rigidity of the structure, like a baguette to any canvas. But, as you understand, the profiled sheet may be different, therefore the edging for it is also available in certain sizes.
• For example, for the sheet MP20, the bar is made 20x22x20 mm, but for C8 it is already 20x10x20 mm. In addition to these varieties, structural elements are produced with curved inwards and rolled edges, which gives rigidity to both the bar itself and the sheet as a whole. Sometimes fences are sheathed with profiled sheeting from two sides, in this case, additional elements are made to order and can be from 80 mm in width.

Use of fence for euroshtaketnik

• Looking at the photo, located above, you will certainly agree that without the use of edging such a fence would look much worse. But even this is not the main thing, because each shtaketin individually represents a rather weak element, and when they are joined together with an additional element, the strength of the whole structure increases.

Council When you overlap the fence with a plank, you should not make a joint butt joint, because water will leak through the seam and this place will be devoid of rigidity. The connection should be made with an overlap, and in the presence of stiffeners (edges bent inward), make trimming on one side.

Intake caps and tides

Fence with a complete set of additional elements - caps, slats and ebb

• Low tides are usually installed on fences that have a parapet of concrete or decorative brick and stone as protection against precipitation. Such a structural additional material is practically no different from window sills, because it performs the same function.

Different ebb colors

• Such elements are usually made by cold rolling galvanized sheet steel and have a polymer or powder coating. It is noteworthy that the ebb are often made by the handicraft method, that is, they are made by a tinsmith with their own hands on an individual order. Thanks to this, it is possible to order products of any width, which will correspond to the thickness of the intake parapet.

Council Ebb tides are most often installed on double-sided corrugated fences with a concrete, brick or stone base. Therefore, the professional sheet on the fence is mounted after fixing the outflow, blocking it, so water will not fall on the upper end of the parapet.

Polymer-coated tin cap

• Caps for fence supports can be made either from concrete or from galvanized tin. The latter method involves a bent sheet construction, and the suture joints are fixed with rivets or screws, but you can also find better products where the joining is done using an internal fold. This method of structural assembly eliminates water flowing under the cap, that is, on the end of the support, from which, of course, increases the price of the product. Painting is made by polymeric or powder method.

Concrete caps for supports

• No less popular are the caps for the pillars of concrete, which can be made of ordinary or decorative (colored) cement. For the production of such elements are used forms of fiberglass or polyurethane, which are poured on the vibrating table. Such products have an advantage over tin, because they do not rust after mechanical damage, and besides, they can be glued together and sealed with potholes.

Conclusion

For installation of additional elements, there is an instruction, which is given by the manufacturer or it is simply advice from the master who made them. Compliance with such recommendations for installation and operation will extend the life of the slats, hubcaps and ebbs, as well as facilitate their installation on a certain type of fencing.