Deprecated: preg_match(): Passing null to parameter #2 ($subject) of type string is deprecated in /web/blog-oremonte.ru/page.php on line 13
How to install the interior door yourself: a description, - Blog about repair

How to install the interior door yourself: a description,

15-01-2018
Doors

Не существует ни одной квартиры без межкомнатных дверей – это факт. Таким образом, выходит, что их установка обязательна, а чтобы сэкономить средства на услугах мастера-установщика, можно прочитать ниже описанный процесс установки и узнать, how to install the interior door yourself.

Installation process

The question of how to install interior doors yourself, you need to decide, starting with the following:

  • It is necessary to check the level of the angle in the room.  You will not succeed without a level and a plumb, be sure to use them.
  • building level is laid horizontally in the doorway, according to the level, points are placed on both sides, after which the distance to the floor is measured. This simple way you can easily determine the length of the rack boxes.

Tip! Leave a gap of 3 mm between the leaf and the box.

To find out how to install the interior door yourself, you must first understand the process of preparing the opening. The essence of this procedure is that the unit normally passes through the opening, and there should be a technical gap of 10-20 mm, which will later be filled with a sealant.

how to install the interior door yourself

Install the door frame

Before you install the interior doors themselves, you first have to purchase them and door frames.

Tip! Order the boxes in the carpentry shop, as the factory ones are not always of good quality. And if you order the door, the competent master will make the canvas from the hinge side be less than 90 degrees, which will prolong the life of your door.

Collecting door frame

Installation process коробки:

  • The door frame is installed according to the level on the side of the arches, while the top should have a “horizon”. In this case, you will need wedge-shaped bars. How to install yourself so that everything was smooth and in place?
  • After placing the box, you must very carefully measure the distance between the racks. As a result, the gap everywhere should get the same - 3 mm.

Also, before you install the interior door with your own hands, you have to assemble the door frame.

It is done as follows:

  • the top of the box and stand is cut at a 45 degree angleand the box itself is placed on a horizontal surface and assembled.
  • to assemble the box, its top and pillars are folded in the shape of the letter “P”, и, если все правильно подогнано, они перпендикулярны друг другу. Если вы не знаете, how to install doors for yourself на этом этапе, попросите кого-нибудь помочь.
  • drill holes in the junction of the box elements diameter is 1 mm smaller than the diameter of the screws.

Tip! Mark with a router, not with a chisel, then install the hinges tightly into the grooves.

Interior door hinges

How to install interior doors and pay proper attention to the hinges? Be sure to lubricate the hinges, engine oil is suitable for this, and you can fasten them with hidden screws. All loops must be on the same axis, which requires a completely flat surface.

To the slope of the door frame is attached anchor bolt, making it possible to adjust the rack box vertically. So, almost figured out how to install interior doors with their own hands.

The next step will be filling the space between the box and the slope with a sealant, in order to improve thermal insulation. Do not use a sealant on the "self-adhesive", choose made from high-quality rubber. Holes from anchor bolts in the door frame are filled with a decorative cork.

We finish with the installation of the door

how to install doors for yourself

The box is then installed in the opening and wedged with specially designed wedges. With the help of a plumb vertically fix the rack for fixing wedges. In accordance with the hanging door leaf attach the opposite rack.

Tip! Place a sheet of cardboard, 3 mm thick between the box and the canvas, this will provide the necessary clearance.

First, the hinges for interior doors are carefully screwed into the box, then into the door leaf, after which you can hang the door leaf itself. Vertical and horizontal adjustable with wedges.

How to install interior doors without the use of foam? That's right - no way. As soon as you make sure that the box and hinges are in the correct position, the box can be pasted over with masking tape to prevent it from being contaminated with mounting foam.

For better adhesion to the foam, the opening must be moistened with water. As a rule, a single cylinder of foam is enough for one door, keep this in mind when purchasing it.

Tip! Do not save on polyurethane foam in any case, as low-quality foam will eventually be felt.

Dries foam for six hours, and complete drying occurs in a day. Dried foam can be cut with a knife. And only after that you can install all the trim.

Before you install the trim, they are cut at an angle of 45 degrees, then attached to the wall with liquid nails or hidden nails that are driven into the wall. If necessary, use box extenders and various additional elements.

For proper preparation of the additional element, it is necessary to measure the depth of the opening, after which you need to subtract ten millimeters. In the door frame an opening is made with a depth and width of 1 cm. First of all, an additional board is installed, which is fixed with self-tapping screws, after which the box is installed into the finished opening and foamed.

That's all. Now you know how to install interior doors with your own hands, what to look for and what materials to use. Happy repair!