Decorating the slopes of the front door from the inside with

The decoration of the slopes from the inside of the entrance door is mainly done with the same material as the lining itself. Only she does not always fit. Therefore, before you make a choice, it is worth looking at photos of finishing options. From the video you can determine the amount of work to be done.

After that, make a decision. Nowadays there are many types of cladding. In this article we will tell about them. Instructions will be given for the performance of work with various materials.

Options for finishing slopes

There are several options for finishing slopes. This is the stucco that is done the most.

It will fit almost any door. You can also make and finish other popular materials, which installation is practically no different. Therefore, we touch on all aspects of finishing.

Slope plaster

This is the most common material that makes the majority of the population. It is the most durable and does not require large maintenance costs.

Execution price is not high and repair is not difficult. Such work is quite possible to do it yourself, and with little cost.

Just follow some rules:

• First you need to prepare the base plane. To begin, clean it from the previous coverage. To do this, use a metal brush;
• Now we do the inspection. If there is exfoliation of the previous coating, then it should be repelled with a hammer and chisel.

Attention: If there are not large cracks on the surface, then it is necessary to expand them to one cm. The fact is that if there is a small crack, then the solution will not get into it and will not completely fill the cavity. It is necessary to expand it to process quality.

• After the work done, we again inspect the surface for the presence of fungus.. If there are dark spots, then they should be treated with antiseptic, which is in retail sale. Do the treatment a couple of times and, moreover, apply a deep penetration liquid;

• After the preparation, the entire surface is covered with primer. It will strengthen the connection of the material with the plane;
• If there is a hole between the frame and the wall, then it must be replaced with construction foam and, after drying, cut off the protruding edges.

We plaster slopes

This is not such a difficult job, as it may seem at first glance. It is necessary to trim slopes for entrance doors in a certain sequence and observing some rules.

So:

• The first cases we need to determine the level of application of the solution. To do this, use the usual flat wooden plank. We apply it to the plane and make adjustment using a level. In this embodiment, we can easily determine the level of the solution. After the plank becomes smooth, we apply a line on it with the help of a pencil or marker. This will be the final coating layer;

Attention: If the desired layer for application is up to one cm. Then you can apply the solution simply on the plane. If this size is larger, then a construction grid should be applied. This will strengthen the bonding of the surfaces and extend the service life of the product.

• Now prepare the solution. You can apply a solution of cement, and you can use the already prepared mixture. For the first option, you need to pass the sand through a sieve and get rid of the garbage and then make the connection in a 1: 3 ratio of cement and sand;
• For a solution from a dry mixture, it is necessary to use a plastic bucket from under the paint for the preparation; it is in this that the batch can be prepared in the most qualitative way. There is a direct bottom and nothing will prevent it from being done qualitatively. Pour into a container dry mixture and begin to add water and at the same time mix. After that we need to make the mass completely homogeneous and lump free. For this it is necessary to use a drill with a nozzle. With its help, you can perform the work of the highest quality;
• We take not big pieces of thick solution and impose it on the plane is not large piles. They must be the right height. These will be the level beacons;
• Using a spatula or trowel, apply the first layer of mortar. Do not immediately put too much. Apply the mixture layer by layer. In this case, you should let the previous one dry before applying the next one;
• When it is 5 mm to finish. Then you need to prepare the finish. It is done as described above. Only it should be applied with a wide spatula over the entire plane. When working use serpyanka for finishing the corner. It will make it stronger and more even;

• After complete drying, we do the processing with construction mesh or sandpaper. If there are shells, then they should be treated with a new solution. So we do to complete the alignment of the surface. After final processing, the surface is covered with primer and paint.

In principle, plastering of slopes is also used for finishing the plane with other materials. The surface is leveled to it and after that the material is fastened.

Finishing other materials

Sometimes the facing of slopes inside the room is done with the use of other materials. To do this, use MDF, drywall (see. We make door slopes of drywall), wood or laminate.

Fundamentally it does not matter what to do this work. It is almost the same. Finishing of the entrance doors from the inside can be done with almost any material.

 So:

• Preparation for lining the base plane has several stages. At first, this cleaning and priming of the surface is done exactly as described above. The lining level is also determined the same way;
• Now we need to install the base for mounting. The most commonly used wooden bar of the desired height.

Attention: When choosing a bar, you should also take into account the thickness of the cladding material. The construction itself will also rise to this height. Before performing the work, the wood should be treated with antiseptic. Which is in the free market. This will significantly extend the life of the wood.

• After the material has dried, we cut it into the required size and fasten it to the surface. Only should take into account the specifics of the plane. She will be subject to fluctuations. Therefore, the connection should be quite tough. To connect use dowels. To do this, we make a hole in the wall with the help of a perforator and a drill with soldered soldering. Do not use dowels from the sets for fastening. Purchase separately plastic and self-tapping screws, the diameter of which should be taken a couple of mm more from the cross-section of the hole. Such a connection will ensure the reliability of fastening;

• If you are finishing MDF, then you should correctly measure the required plates and order them. Just do it right, otherwise no one will accept the material back from you. For laminate, the material is simply cut to the desired size and the edge is glued with veneer (see Veneered doors: what it is and how it is done) and then the connection is made. For drywall, sheets are cut into the desired elements and then applied in the work. Cutting is performed with a sharp knife;
• Now we do the mount. This can be done with glue. Then it should be applied to the surface and pressed, then hold until the liquid dries;
• A tighter connection is made with screws. To do this, make a hole in the panel with a drill and drill. After this, we perform nudging for the cap of the screw, which is screwed and the hole is closed with a plastic plug;
• Along the edge of the wall you will have a small gap. It is covered with a plastic corner. The gap near the edge just clogged with putty.

Now you know how to trim the front door from the inside and slopes. To do this, you should know the most important thing is that you should not hurry and make the right measurements.

The design makes it stiff, which must withstand vibrations when the door is operating. Then the work does not take much time and will serve you for many years.