Installation of imitation timber: fastener nuances,

Suspension beams are always very well suited for interior decoration. Simple installation imitation timber - do it yourself will not only hide the irregularities of the walls, but also become a good material with which you can achieve sound insulation. Plus, here you can always point out the low cost of the raised rail.

Mounting everything by yourself

Imitation is called a grooved wood panel, which can be brought under a kind of lining. The difference from the classic plastic lining is not only in the material, but also in size, in the absence of characteristic recesses on the front side.

At the same time, the material externally completely copies the structure of the natural timber (oak, pine, larch). Thus, it is possible to use the analogue of this tree in work with the interior, indoors, and with external works.

Properties

Before you start working with the material, you must understand what qualities and properties it possesses:

• Practicality. It is this property that can be brought to the fore, because it allows you to work independently, and therefore seriously save.
• External data The identity of the natural bar allows you to use imitation in many rooms, and almost everywhere it will look great.
• Environmental friendliness. The material contains no hazardous substances and compounds, which makes it possible to use it in residential premises.
• Special heat treatment prevents the product from cracking and deforming.

Note! Coniferous woods serve as raw material for the production of false bars, and this gives the entire product additional properties that are related to needles.

The product is produced in several dimensional grids, but the most common are:

• Length - 3-6 meters.
• Thickness can vary from 20 to 35 mm.
• The most demanded width is 140 mm.

With all the indisputable advantages, it is necessary that the installation instructions for imitation lumber are fully followed, because otherwise, all the advantages of this material do not matter.

Installation

The installation process begins not so much from the work itself as from bringing the material to the installation site. This is a very important point, since the imitation must fully acclimatize to the conditions of the room.

The delivery time is 7-10 days before the start of the main stages of the construction of a log house.

Facade

First of all, the installation of the insulated suspended beam on the facade will be considered. This will require:

• Calculate the entire area of ​​the walls.
• Purchase the required amount of insulation, for example, mineral wool.
• Purchase a bar for the device of the batten, section 50x50 mm.
• Screws on wood.
• Roulette.
• Screwdriver and drill.
• Steam insulation film.

In principle, the installation technology of imitation timber practically does not differ from any type of cladding, and it looks like a step by step:

• The walls of the house are cleaned and primed.
• Mounted crate of timber with a pitch of 0.6 meters.
• The vapor barrier film is installed.
• Mineral wool mats are installed. The fastening of cotton wool may not be necessary, since the mats will closely enter the distance between the parts of the batten.

Note! As with any lining, the gap between the wall and the imitation must be present, and be at least 10 mm. This is necessary for normal, natural air circulation. It is for this purpose in the walls will need to leave a few holes for the duct.

Once everything is ready to install the raised beam, you can begin the installation. The first board is installed below. Be sure to align with the level, it will be a guide and all facing will go along it.

The board is set with a spike upwards, so water will not accumulate in the slots. The board is fixed with a screw, which at an angle of 45 degrees is pushed into each connection with the crate. The self-tapping screw is installed in a thorn.

The next board is inserted into the spike groove, but so that it does not fit completely to the previous one. It is necessary to remain a small gap of 1-2 mm. This will prevent the surface from deforming due to seasonal temperature changes.

Despite the fact that the cost of installation of imitation timber is low enough, you can still do everything yourself, this can be a rehearsal for work that can be done indoors.

Interior

As for the installation of a false beam indoors, here everything is almost the same, if we talk about installing rails, but it does not make sense to install a vapor barrier film and insulation.

To keep the material in excellent condition for a long time, it is treated with special impregnations.

In principle, sheathe the walls in the room, no one forbids installing and insulating material, but it should be done only if no work has been carried out to insulate the building from the outside.

Conclusion

The imitation setup technology is really incredibly simple. If there was any experience installing siding, or thermopanels, is dry, it will be even easier to cope with the false beam.

But if you approach the work without any experience at all, there will be no problems either, the technology itself will submit to any novice builder.

It is important to note that the price of the material can be from 250-280 rubles per cubic meter, which is quite convenient and not at all expensive.

Conclusion

Ideal material makes not only its appearance, which fits perfectly into a large number of interior and exterior solutions, but also a long service life.

And the latter can be achieved using various impregnations, after which the wood acquires additional qualities, and this makes the installation of imitation timber with your own hands an even more reasonable choice as a lining. The video in this article is ready to visually confirm all of the above, we look!