How to make a concrete tile in concrete: features of tools

28-04-2018

Building

Concrete is one of the most durable building materials, especially if additional reinforcement was used in its manufacture. However, sometimes it becomes necessary to make certain changes to the structure or to put a system of wires and pipes, which is usually associated with the violation of the integrity of such structures. Therefore, the question of how to make a concrete wall is very interesting for modern masters.

Amateur photo, the process of making pens using a conventional punch

Features of materials and tools

To begin with, it must be said that this process is rather laborious and complex. Therefore, the easiest way is to invite specialists to perform it. However, the cost of piles in concrete is usually quite high and many craftsmen prefer to do it themselves.

Professional shtrober with a protective casing, which also performs the functions of a dust collector, followed by discharging to a vacuum cleaner

Tool

It is best to use a specialized tool to accomplish the task. This includes the strober on concrete, which was developed specifically for these purposes. However, you must immediately pay attention to its power and quality nozzles.

Original punching nozzles are more suitable for brick walls, and when working with concrete it is better to find a replacement for them

Also in such cases, cutting of reinforced concrete with diamond circles is used. In this part of the site will have to be knocked out manually using a hammer and chisel.
Some masters for such tasks use diamond drilling holes in concrete. However, drilling a large number of holes in concrete is quite tiresome and does not always justify itself.

A professional tool will not only facilitate the work, but will also save a huge amount of time, which is quite often equivalent to money.

It is worth noting that modern masters use a lot of various devices to perform this work. At the same time, many of them are not intended for these purposes at all, but in response to the question of the better way to shade concrete walls, they all definitely stop at the strober.

Tip! A professional tool for these works is quite expensive. Therefore, it is much easier to rent it.

It is also possible to use such a tool for such work, but for safety reasons it is not recommended.

Different material

When concrete is crushed, it is very important to know what exactly a concrete surface is made of. It is important not only to select the appropriate cutting element, but also to determine the location of the reinforcement or wires.

Most professional equipment of this type is immediately equipped with a device for detecting metal in the wall and information about its presence is displayed on the indicator

The easiest way is to make aerated concrete. This is due to the fact that it has a bubbly structure, and to destroy small partitions is much easier than making grooves in a monolithic slab. The same applies to the products of foam concrete, having similar characteristics.

When a strobe is created in aerated concrete, it is subsequently worth covering it with a thin layer of cement mortar to seal all the holes. This material may have through gaps and it is better to create additional protection.

Even a simple chisel and hammer can be used with a porous material.

The hardest thing to do is work on a reinforced concrete wall. This is due to the fact that in addition to the monolithic stone will have to deal with metal fittings. Therefore, the strobe in the concrete of this type is done only with appropriate equipment.

Tip! When purchasing a wall chaser for aerated concrete or concrete, it is worthwhile to buy in advance all the necessary nozzles that will allow you to work on surfaces from any material.

Almost always, this process is associated with the release of large amounts of dust, which accordingly implies the use of personal protective equipment.

Recommendations of the masters

Professional craftsmen are advised to purchase a special device for detecting wires or fittings in the wall. Its price is not as high as the cost of frequent tool repairs or the purchase of the cutting part in contact with metal.

It is worth noting that if such a device is on the instrument, then its readings may not always be true or they may be noticed too late.

Do not remove the protective cover from the electric tool, even if it interferes with the specific work

Some masters use a tool that is completely unsuitable for such work.. At the same time, they remove the protective covers for convenience. However, the installation manual clearly states that this is strictly prohibited and may lead to injury.
When performing such work, a large amount of dust appears, even when using special systems for its removal.. Therefore, making work with your own hands, first of all, you need to take care of personal protective equipment. Special attention should be paid to special glasses and a respirator.

Connecting a special vacuum cleaner will significantly reduce the level of pollution

Conclusion

After reading the video in this article, you can learn more about this process and tools for its implementation. At the same time, based on the text above, it is necessary to conclude that such work is associated with a lot of difficulties caused by the strength of concrete.